🛠️Utility Hub
💬Feedback
🏠 Home

Pipe Offset & Cut Length Calculator

Cut lengths for offsets, 45° and rolling offsets and centre-to-centre runs, with elbow allowances for KS butt-weld, KS threaded and ASME fittings.

1. Fitting standard and size

KS B 1522 (JIS B 2312) butt-weld fittings used in Korea. 45° values differ from ASME by 3.4 mm per elbow at 50A.

2. Dimensions

Elbow (same at both ends)
mm
Weld root gap (per joint)

3. Result

Pipe cut length
361.1mm
KS butt-weld 50A · 45° long radius
Travel (centre to centre)offset × 1.414424.3 mm
Run (advance)along the main run300.0 mm
Elbow allowance (each)standard table value31.6 mm
Total deductedallowance × 263.2 mm
Cut length361.1 mm
Offset 300Run 300✂ 361.1Travel 424Elbow centre
Pipe to cutFitting allowanceAdjoining pipe

Fittings vary by 1–2 mm between makers; measure the first one.

Allowance table — KS butt-weld

Size90° LR90° SR45° LR
15A38.1-15.8
20A38.1-15.8
25A38.125.415.8
32A47.631.819.7
40A57.238.123.7
50A76.250.831.6
65A95.363.539.5
80A114.376.247.3
90A133.488.955.3
100A152.4101.663.1
125A190.512778.9
150A228.6152.494.7
200A304.8203.2126.3
250A381254157.8
300A457.2304.8189.4
Offset multipliers
AngleTravel = offset ×Run = offset ×
11.25°5.1265.027
22.5°2.6132.414
30°2.0001.732
45°1.4141.000
60°1.1550.577

Dimensions are transcribed from KS (JIS) and ASME tables; verify on site.

Share this tool

Related Tools

🔧Pipe Size, Slope & Flow Calculator
🏗️Metal Weight Calculator
📖Construction Site Glossary
📝Character Counter
📐Pyeong to m² Converter
🔢Unit Converter

Pipe offset and cut length with automatic fitting allowances

When a pipe is offset around an obstacle, the piece between the elbows is not cut to the offset distance, because each elbow takes up length. The fitting allowance (take-off, or centre-to-end) must be deducted at both ends. This calculator includes allowances for KS B 1522 (JIS B 2312) butt-weld elbows used in Korea, KS B 1533 (JIS B 2301) threaded malleable elbows and ASME B16.9 elbows, and turns an offset into travel, run and cut length. A 300 mm offset with 50A butt-weld elbows needs 147.6 mm of pipe with 90° elbows (300 − 2 × 76.2) and 361.1 mm with 45° elbows (424.3 − 2 × 31.6). Threaded elbows deduct centre-to-end minus thread engagement, 23 mm for 25A. It also handles rolling offsets, elbows cut to any angle, weld root gaps and centre-to-centre runs, with a scale drawing, allowance tables and offset multipliers.

Common Use Cases

🔧
Offset Around Obstacles
Pick the size and elbow to get the cut length and how far the run advances.
🔩
Threaded Pipe
Threaded fittings deduct centre-to-end minus engagement — 23 mm for 25A, not 38 mm.
📐
Drawing Dimensions
Turn centre-to-centre dimensions into cut lengths by deducting both fittings and weld gaps.
🧭
Rolling Offsets
200 mm across and 150 mm up is a 250 mm true offset; the tool also gives the roll angle.

How to Use

  1. 1
    Pick Standard and Size
    KS butt-weld, KS threaded or ASME, 15A to 300A.
  2. 2
    Pick a Calculation
    Offset, rolling offset or centre-to-centre to cut length.
  3. 3
    Enter Elbow and Distance
    Choose 90°, 45° or a cut-down angle and enter the offset or C-C dimension, plus weld gap.
  4. 4
    Read the Cut Length
    Check cut length, travel, run and deductions on the scale drawing, then copy.

Frequently Asked Questions