๐Ÿ› ๏ธUtility Hub
๐Ÿ’ฌFeedback
๐Ÿ  Home

Cable Tray Slope & Offset Fabrication Calculator

Enter rise and run to get V-cut and slit dimensions for both bends, marking distance and support positions, with a 3D fold preview.

STEP 1

What kind of segment?

From bottom to top of rail

How to bend cable tray in the field (V-cut formula)

  1. Find the angle โ€” with rise H and run L, the bend angle is ฮธ = atan(H รท L). Factory elbows come in 30ยฐ, 45ยฐ, 60ยฐ and 90ยฐ, so field bends of 45ยฐ or less are the practical range.
  2. Size the V-cut โ€” for an up or down bend use the side-rail height h; for a horizontal bend use the tray width w. Half-width of the notch = reference ร— tan(ฮธ/2), and the full notch is twice that. A 100 mm (4 in) rail bent 30ยฐ needs 26.8 mm each side (53.6 mm total); at 45ยฐ it is 41.4 mm each side (82.8 mm total). A 300 mm (12 in) wide tray offset 30ยฐ sideways needs 80.4 mm each side.
  3. Cut depth and side โ€” cut the V the full depth of the reference (rail height or tray width) on the inside of the bend only. On the side that opens up, make a straight slit and cover the gap with a splice plate.
  4. Mark the distance โ€” the bottom between the two bends equals the slope length โˆš(Hยฒ + Lยฒ). For a horizontal offset, add back the length lost to the V-cuts; the calculator above does this automatically.
  5. Fix and support โ€” bolt the bend with adjustable splice plates and place supports within 600 mm (2 ft) of each bend and splice, as NEMA VE 2 recommends.

Share this tool

Related Tools

โšกWire Size Calculator (AWG & mmยฒ)
๐Ÿ”งPipe Size, Slope & Flow Calculator
๐Ÿ—๏ธMetal Weight Calculator
๐Ÿ“Pipe Elbow Offset Calculator
๐Ÿ“Character Counter
๐Ÿ“Pyeong to mยฒ Converter

What is the Cable Tray Slope & Offset Fabrication Calculator?

This tool gives electricians the numbers needed to field-cut and bend a channel or ladder cable tray for a slope (rise or drop) or a sideways offset. Enter the rise H and run L, or pick 30ยฐ, 45ยฐ or 60ยฐ with a rise, and it returns the bend angle and slope length, then for each of the two bends in the segment tells you whether it is a V-cut or a straight slit, how far to mark on each side of the centerline, and the marking distance A between the bends. In a vertical bend the bottom is the fold axis, so the bend where the rails close (start of a rise, end of a drop) needs a V-cut and the bend where they open needs a straight slit. In a horizontal bend the bottom gets the V-cut, the inner rail section is removed and the outer rail folds. A rotatable 3D view shows the flat tray folding to the real angle, alongside a true-proportion marking detail and support positions based on NEMA VE 2.

Common Use Cases

โœ‚๏ธ
Rises and Drops
For a 30ยฐ drop of 0.25 m from a ceiling rack, get where each bend needs a V-cut or a slit and the marks to make, such as 26.8 mm each side of center on a 100 mm rail.
โ†”๏ธ
Offsets Around Columns
When the tray must shift sideways around a column or duct at the same level, get the angle from offset and run, the V-cut width in the bottom and the length of inner rail to remove.
๐ŸงŠ
See the Fold in 3D
Rotate a 3D model that folds from flat to the real angle, so new installers can see exactly which part is cut away and which part bends before touching the grinder. V-cut width, rail height, tray width and the current bend angle are labelled on the model.
๐Ÿ”ฉ
Supports and Elbow Alternative
Get support positions on the slope that respect a maximum span and the 600 mm rule at bend joints, plus the nearest factory elbow size and the run needed if you buy fittings instead.

How to Use

  1. 1
    Pick the Segment and Tray
    Choose rise, drop or side offset to match the site, then the tray width and side rail height. Rail height is the reference for vertical bends and tray width for horizontal bends.
  2. 2
    Enter Dimensions
    Pick 30ยฐ, 45ยฐ or 60ยฐ and enter the rise (or offset), or enter measured H and L. Measure at the tray bottom for vertical bends and at the tray centerline for offsets, as shown in the diagram.
  3. 3
    Check Each Bend
    Switch between bend 1 and bend 2 to see half width, full width and cut depth. Use the 3D view and true-proportion detail to mark both sides of the centerline, and space the bends by distance A.
  4. 4
    Place Supports and Share
    Enter the maximum span from the design or manufacturer to get support positions on the slope, then copy all results to send to your foreman or crew.

Frequently Asked Questions